TPS259631DDAR

Texas Instruments
595-TPS259631DDAR
TPS259631DDAR

Fabricante:

Descripción:
Controladores de voltaje intercambiables en caliente 2.7-V to 19-V 85moh m 0.13-2A eFuse wit A 595-TPS259631DDAT

Modelo ECAD:
Descargue Library Loader gratis para convertir este archivo para su herramienta ECAD. Conozca más sobre el modelo ECAD.

En existencias: 5,073

Existencias:
5,073 Se puede enviar inmediatamente
Plazo de entrega de fábrica:
6 Semanas Tiempo estimado de producción de fábrica para cantidades superiores a las que se muestran.
Mínimo: 1   Múltiples: 1
Precio unitario:
$-.--
Precio ext.:
$-.--
Est. Tarifa:
Empaque:
Envase tipo carrete completo (pedir en múltiplos de 2500)

Precio (USD)

Cantidad Precio unitario
Precio ext.
Cinta cortada / MouseReel™
$0.80 $0.80
$0.574 $5.74
$0.517 $12.93
$0.455 $45.50
$0.425 $106.25
$0.407 $203.50
$0.392 $392.00
Envase tipo carrete completo (pedir en múltiplos de 2500)
$0.376 $940.00
$0.357 $2,677.50
† $7.00 Se agregará y calculará la tarifa de MouseReel™ en su carrito de compras. Ningún artículo de MouseReel™ se puede cancelar ni devolver.

Embalaje alternativo

N.º de artículo del Fabricante:
Embalaje:
Reel, Cut Tape, MouseReel
Disponibilidad:
En existencias
Precio:
$0.95
Mín.:
1

Producto similar

Texas Instruments TPS259631DDAT
Texas Instruments
Controladores de voltaje intercambiables en caliente 2.7-V to 19-V 85moh m 0.13-2A eFuse wit A 595-TPS259631DDAR

Atributo del producto Valor de atributo Seleccionar atributo
Texas Instruments
Categoría de producto: Controladores de voltaje intercambiables en caliente
RoHS:  
Controllers & Switches
125 mA to 2 A
19 V
2.7 V
1 Channel
193 uA
- 40 C
+ 125 C
SMD/SMT
SO-PowerPad-8
Reel
Cut Tape
MouseReel
No
Marca: Texas Instruments
País de ensamblaje: CN
País de difusión: US
País de origen: CN
Tensión de entrada / alimentación - Máx.: 19 V
Tensión de entrada / alimentación - Mín.: 2.7 V
Sensibles a la humedad: Yes
Tipo de producto: Hot Swap Voltage Controllers
Serie: TPS2596
Cantidad de empaque de fábrica: 2500
Subcategoría: PMIC - Power Management ICs
Peso de la unidad: 95.600 mg
Productos encontrados:
Para mostrar productos similares, seleccione al menos una casilla de verificación
Seleccione al menos una de las casillas de verificación anteriores para mostrar productos similares en esta categoría.
Atributos seleccionados: 0

Esta funcionalidad requiere que JavaScript esté habilitado.

CNHTS:
8542399000
CAHTS:
8542390000
USHTS:
8542390090
MXHTS:
8542399999
ECCN:
EAR99

TPS2596xx 2.7V to 19V eFuses

Texas Instruments TPS2596xx 2.7V to 19V eFuses with integrated FET hot-swap devices are highly integrated circuit protection and power management solutions in a small package. The devices provide multiple protection modes using very few external components and are a robust defense against overloads, short circuits, voltage surges, and excessive inrush current. The output current limit level can be set with a single external resistor. It is also possible to get an accurate sense of the output load current by measuring the voltage drop across the current limit resistor. Applications with particular inrush current requirements can set the output slew rate with a single external capacitor. For the TPS25962x variants, internal clamping circuits limit the output to a safe fixed maximum voltage (pin selectable) with no external components in case of an input overvoltage condition. The Texas Instruments TPS25963x variants allow setting a user-defined overvoltage cutoff threshold.

LM5060 High-Side Protection Controllers

Texas Instruments LM5060 High-Side Protection Controllers with Low Quiescent Current offers intelligent control of a high-side N-channel MOSFET during normal on/off transitions and fault conditions. The constant rise time of the output voltage results from the inrush current control. Both an Input UVLO (with hysteresis) and a programmable input OVP are provided, with an enable input offering a remote on or off control. The initial start-up VGS fault detection delay time, the transition VDS fault detection delay time, and the continuous over-current VDS fault detection delay time is programmed from a single capacitor. The MOSFET is latched off until either the enable input, or the UVLO input is toggled low and then high when a detected fault condition persists longer than the allowed fault delay time.